Kitchen Sink and Faucet Installation in Franklin, TN

The sink is the most used spot in any kitchen. You stand at it more than at the range, and the faucet is the one fixture you touch dozens of times a day. In many Franklin and Brentwood kitchens the original setup is a shallow double bowl sink dropped into a laminate or tile counter, with a short faucet that cannot fill a tall pot.

Sinks and faucets are also tied to everything around them. An undermount sink is cut into the stone and sized to the cabinet below it. A pot filler needs a water line in the wall before the tile goes up. Moving the sink to an island means rerouting the drain under the floor. And Middle Tennessee water is moderately hard because of the limestone it runs through, so scale and water spots are a real factor when you choose a finish. We select the sink and faucet during design, alongside the cabinets and countertops, so each one fits the others.

What Sink and Faucet Installation Includes

• An in-home consultation where we look at how you use the sink now, measure the sink base cabinet, and check the plumbing below it
• Sink and faucet selection drawn into your scaled layout, with the sink model fixed before the countertops are templated
• Undermount, apron front, or drop in sink installation, coordinated with the stone fabricator and the cabinet below
• Faucet installation with new shutoff valves and supply lines
• Disposal installation, with a wall switch or a countertop air switch
• Pot fillers, filtered water taps, and instant hot taps, with the water lines and outlets they need
• Sink relocation, including moving a sink to an island or under a window
• Coordination of the plumbing work, along with the permits the job requires

How a Sink and Faucet Project Runs

1. Start at the sink you have. At the first visit we look at the cabinet size, the window above, the plumbing in the wall and under the floor, and how you work at the sink.
2. Choose it in the design. The sink, faucet, and accessories appear in your scaled layout and 3D renderings. You approve them before anything is ordered.
3. Fix the price in writing. You get a fixed written price before demolition. Changes only happen when you ask for them, and they are priced in writing first.
4. Have the sink on site early. The sink arrives and is inspected before demo. The fabricator templates the countertop to the actual sink after the cabinets are installed, not to a drawing.
5. Rough in, then set and connect. Water lines and drains are moved while the walls and floor are open. The sink is mounted with the countertop, and the faucet, disposal, and taps are connected and tested after.
6. Walk it with your project lead. We run every fixture with you, check for leaks, and show you each shutoff valve.

When to Replace or Relocate Your Sink

• You are replacing the countertops, which is the natural time to change an undermount sink
• The sink is too shallow or too divided to fit a sheet pan or a stock pot
• The faucet drips, has lost pressure to scale, or will not reach the corners of the bowl
• The sink faces a wall and you would like it at a window or on an island facing the room
• You want filtered water without a pitcher in the refrigerator

Sinks are replaced most often with new stone. See our kitchen countertops page for how templating and fabrication work.

Sink, Faucet, and Fixture Choices That Matter

Sink material and shape. Stainless steel in a heavier gauge is quiet, forgiving, and easy to live with. A brushed finish hides scratches and water spots better than a mirror finish. Fireclay and enameled cast iron suit apron front sinks and traditional kitchens, but they are heavy, they need a sink base built for them, and fireclay dimensions vary enough that the cabinet and stone are fitted to the actual sink. A large single bowl handles sheet pans and roasting pans.

Faucets and finishes. A pull down faucet with a high arc covers most needs. Check the spout reach against the bowl so the water lands near the drain, not the back wall. With moderately hard water, brushed nickel, stainless, and satin brass stay presentable between cleanings. Polished chrome and matte black show every spot.

Pot fillers, disposals, and filtered water. A pot filler is mounted above the range and plumbed through the wall, so its height is set against the range and the backsplash tile layout. A disposal is sized to the household, and a countertop air switch keeps the control off the backsplash. If your home is on a septic system, tell us, because it affects the disposal choice. Filtered and instant hot taps need space, a water connection, and often an outlet inside the sink base, so we plan the cabinet interior around them.

Moving a sink to an island. The sink can go almost anywhere the drain can reach. Over a crawl space or an unfinished basement, the new drain is run below the floor. On a slab, the concrete is cut and patched. An island sink also needs a venting method the local codes office accepts. We work this out in the design phase with the island plan.

What Drives the Cost of Sinks and Faucets

• The sink and faucet you select, since materials and finishes vary widely
• Whether the sink stays in place or moves
• What is under the floor, with a slab costing more to open than a crawl space or basement
• Added fixtures such as a pot filler, a filtered water tap, or a second prep sink
• Cabinet changes for an apron front sink or a wider bowl
• The condition of the existing shutoff valves, supply lines, and drain

Every project gets a fixed written price after the design is approved, before demolition begins. The only changes are ones you ask for, priced in writing first.

Plan Your Sink and Faucet With Kings

The right sink and faucet make daily work in the kitchen easier, and the wrong ones are hard to change once the stone is cut. We will measure what you have, show you options that fit, and draw them into the design. Book a kitchen consultation or call (615) 555-0100.

Can I replace my kitchen sink without replacing the countertops?

Sometimes. A drop in sink can usually be swapped for another of the same size. An undermount sink is attached to the underside of the stone, and the cutout was made for that exact model, so a replacement has to fit the existing opening. Changing to a larger sink or an apron front sink usually means new countertops and sometimes a new sink base cabinet. We measure the opening and tell you which case applies.

Can you move a kitchen sink to an island?

Yes, in most homes. The supply lines are the easy part. The drain needs a continuous slope back to the main line and a way to vent, and the route depends on whether the kitchen sits over a crawl space, a basement, or a concrete slab. Moving plumbing typically requires a permit. We check the framing and the drain route during design, so the answer and the cost are known before anything is ordered.

What sink and faucet finishes hold up to hard water in Franklin?

Middle Tennessee water is moderately hard, so mineral spots and scale show up on anything dark or mirror polished. Brushed stainless sinks, brushed nickel, and brushed or satin brass faucets hide spotting best. Matte black and polished chrome look sharp but need wiping down to stay that way. Whatever the finish, a faucet with a ceramic cartridge and an aerator you can unscrew and clean will handle scale better over time.

Is a pot filler worth installing?

It depends on how you cook. If you fill large stock pots often, a pot filler saves carrying water across the kitchen. It also adds a water line behind the range with no drain below it, so it needs a shutoff you can reach and it should have two valves. The line has to go in the wall before the backsplash tile, which is why it is decided during design, not after.